A long drive from downtown Houston, in Walker County, a gravel or grass drive in Huntsville turns soft in a wet week, and a soft drive can move the install day.
The five stones we cut
We cut and install five materials, and each one fits a different kind of kitchen. Granite is natural stone, quarried mostly in Brazil and India. It handles normal pan heat and resists scratching well, and it needs a penetrating sealer. Quartz is engineered: about 90 percent ground quartz bound with resin and pigment. It never needs sealing, and its pattern holds from one slab to the next. The resin is its weak point, since sustained heat above about 300 F, harsh solvents and direct sun all damage it, so quartz stays indoors.
Quartzite is natural stone too, quartz sandstone fused by heat and pressure. It is harder than granite, carries veining that reads like marble and needs sealing. A few stones sold as quartzite are really dolomitic marble and etch like marble, so it pays to know which kind a slab is before you buy it. Marble is the soft one. Lemon, vinegar and wine etch it, it scratches and it wears a patina over time, which is why people choose it for a vanity, a fireplace surround or a baking station, and for a kitchen when they like the patina. Porcelain comes in large, thin slabs with the pattern printed on the face. It resists heat, sun and stains, which makes it a strong choice outdoors, though a chip in porcelain is hard to repair.
Outdoor kitchens
An outdoor counter takes full sun, heavy rain and the heat of a grill, so the stone has to handle all three. Granite, quartzite and porcelain do. Quartz does not: sunlight yellows its resin on any patio, covered or open, so we never install quartz outside. The base under an outdoor top is built by others and must be finished and level before we template. From there the job runs like a kitchen, with the grill and sink openings cut in our shop.
Vanities, fireplaces and backsplash
Stone goes well beyond the kitchen. Vanity tops can run in 2 cm stone, and when the sizes work, a small vanity can come out of the kitchen slab. A fireplace surround can match the kitchen or contrast with it, and marble is a classic there, since a surround sees little wear. Backsplash can stop a few inches above the counter or run full height to the upper cabinets, and a full-height splash cut from the counter slab carries the pattern up the wall. Each of these starts with the same free estimate as a kitchen.
From estimate to install
You will see us three times. The first visit is the free estimate. We measure enough to price the job, check the cabinets for level, look at the sink and the cooktop and bring samples, so you can see each stone in your own light. The written price lists the stone, the edges, the cutouts, tear-out and the sink install line by line.
The second visit is the template. It happens once the cabinets are set and level. Our templater records the room digitally, which catches walls that are out of square, and settles the seam placement and the overhangs with you. Nothing is cut before that. In our shop, the slab is then cut to the template, with the sink and cooktop openings cut and the edges polished.
The third visit is the install. The crew removes the old tops and takes them away, sets the stone on the cabinets, fills the seams with epoxy tinted to the stone and sets the sink. Faucet holes are drilled on site at install, where the faucet will sit. Natural stone gets sealer, and the crew cleans up before it leaves.
Planning the template visit
The drive to a house well outside Houston takes time, so it helps to have everything the template depends on ready before that visit: the cabinets set and level and the counters cleared. The install brings the finished tops, the epoxy and the sealer on the same truck.
Where we work and how to start
Other places near Huntsville on our list: Willis, Montgomery and Coldspring.
If you are planning new countertops in Huntsville, send the estimate form or give us a call. We bring the samples, and you bring the questions.